Share to
SHIPPING AND PICKUP INFORMATION

RelojFROM 8 TO 18 HRS

Despacho
SHIPPING
Pay your order before 12:00 hrs and your order will be shipped on the same day, otherwise will be shipped the next working day.
Shipping arrival date will depend on the city and commune you have selected.
Retiro
IN-STORE PICK-UP
Pay your order and once we confirm your payment, you can pick-up your order on our store from 8 AM to 6 PM. Payments are confirmed in no more than 4 working hours. 
*This method is only available on our Santiago store
Arduino Ethernet Shield 2
SKU MCI01834
Price
24.290
Discount by Quantity
If you buy 10 pay $ 22.350 each one.
If you buy 25 pay $ 22.350 each one.
Availability
Tienda Santiago : Agotado
Viña : Disponible
Notificarme cuando este producto este en stock

Compatibility:

Uno PICARO

Description:

The Arduino Ethernet Shield 2 allows an Arduino Board to connect to the internet. It is based on the Wiznet W5500 Ethernet chip (datasheet). The Wiznet W5500 provides a network (IP) stack capable of both TCP and UDP. It supports up to eight simultaneous socket connections. Use the Ethernet library to write sketches that connect to the Internet using the Shield. The Ethernet Shield 2 connects to an Arduino Board using long wire-wrap headers extending through the Shield. This keeps the pin layout intact and allows another Shield to be stacked on top of it.

The most recent revision of the board exposes the 1.0 pinout on rev 3 of the Arduino UNO Board.

The Ethernet Shield 2 has a standard RJ-45 connection, with an integrated line transformer and Power over Ethernet enabled.

There is an onboard micro-SD card slot, which can be used to store files for serving over the network. It is compatible with the Arduino Uno and Mega (using the Ethernet library). The onboard micro-SD card reader is accessible through the SD Library. When working with this library, SS is on Pin 4. The original revision of the Shield contained a full-size SD card slot; this is not supported.

The Shield also includes a reset controller, to ensure that the W5500 Ethernet module is properly reset on power-up. Previous revisions of the Shield were not compatible with the Mega and needed to be manually reset after power-up.

The current Shield has a Power over Ethernet (PoE) module designed to extract power from a conventional twisted pair Category 5 Ethernet cable.

Note:  This card is compatible with Arduino IDE 1.7.4. You can download it from this link here.

PoE module features as follows:

  • IEEE802.3af compliant
  • Input voltage range 36V to 57V
  • Overload and short-circuit protection
  • 12V Output
  • High efficiency DC/DC converter: typ 85% @ 80% load
  • 1500V isolation (input to output) 

The Shield does not come with a built in PoE module, it is a separate component that must be added on.

Arduino communicates with both the W5500 and SD card using the SPI bus (through the ICSP header). This is on digital pins 10, 11, 12, and 13 on the Uno and pins 50, 51, and 52 on the Mega. On both boards, pin 10 is used to select the W5500 and pin 4 for the SD card. These pins cannot be used for general I/O. On the Mega, the hardware SS pin, 53, is not used to select either the W5500 or the SD card, but it must be kept as an output or the SPI interface won't work.

Note that because the W5500 and SD card share the SPI bus, only one at a time can be active. If you are using both peripherals in your program, this should be taken care of by the corresponding libraries. If you're not using one of the peripherals in your program, however, you'll need to explicitly deselect it. To do this with the SD card, set pin 4 as an output and write a high to it. For the W5500, set digital pin 10 as a high output.

The Shield provides a standard RJ45 Ethernet jack.

The reset button on the Shield resets both the W5500 and the Arduino Board.

The Shield contains a number of information LEDs:

  • ON indicates that the Board and Shield are powered
  • LINK indicates the presence of a network link and flashes when the Shield transmits or receives data
  • FDX indicates that the network connection is full duplex
  • 100M indicates the presence of a 100 Mb/s network connection (as opposed to 10 Mb/s)
  • ACT flashes when RX or TX activity is present

Features:

  • Requires an Arduino Board (not included)
  • Operating voltage 5V (supplied from the Arduino Board)
  • Ethernet Controller: W5500 with internal 32K buffer
  • Connection speed: 10/100Mb
  • Connection with Arduino on SPI port
Warranty 3,0 Months
Weight 0,080
height 1
Width 1
Volume 0,0
Products Accesories